Swiss Files USA, LLC

Arcade Files


Making and Using Tools - Saws and Saw Tools

  Poor Boy's Split Nuts by Leif Hanson 1 of 3  

The screws and nuts that hold a saw handle onto its blade are getting to be either hard to find, or are exceedingly expensive. The standard issue nuts from the hardware store are simple plated steel, and are not consistent in length in my experience. The brass split nuts are available, but are limited in supply and quite expensive at about $5 each plus shipping at the time of this writing.

I thought to myself that I could make them almost as well using a few simple tools found in most woodworking shops - and then I would be able to claim that the saws I make are made entirely by myself, something I thought would be kind of cool to be able to do.

Materials and Tools Required

The split nuts themselves will be manufacture from 10-24 (or 10-32) threaded brass rod (1" long, from McMaster Carr) and plain 9/16" brass rod (9/16" is a common size on most saws with split nuts, but I've also seen 1/2" used), both available from good metal suppliers online (such as McMaster Carr or MSC Direct). Tools needed are a hacksaw, a drill press, a 10-24 (or 10-32) TPI tap, a disk or belt sander, and finally a grinder outfitted with a de-burring and buffing wheel. A jig for making the nuts will be crafted out of some 8/4 ash, some 1/8" plate steel, and a threaded insert.

To make the bolts, a torch (along with all the necessary accoutrements) is necessary for silver-soldering the nut to the threaded brass. An oxy-acetylene torch is the best tool for this job - however, here I am use one of those $50 welding kits that use a small bottle each of MAPP and oxygen gas. These small kits supply plenty of heat for the job, and are much less expensive than buying a full oxy-acetylene rig. If you do a lot of soldering, this is not very cost efficient method - but for occasional use, they works fine.

You will also need some silver solder and flux - I use a brand called "Stay-Silv 45" for the best results. This should be available at most good welding supply stores.

A Simple Jig, and Making the "Tube"

What's needed first is a way to drill a hole through the center of the brass rod in order to thread the nut. The hole must be sized for the size thread you want to tap, and centered in the rod to be proper. The only way to do this is to build a simple jig to hold the brass rod upright so the hole can be drilled into it's center. You will see the jig in many of the following pictures here, and I won't go into too much detail on it because of it's simplicity.

Using a forstner bit that's the size rod I am using, I drill a vertical hole into some 8/4 ash, not all the way through, leaving about 1/2" of wood at the bottom so the rod won't fall through. I then pick a spot on it's side near the top and drill an additional 3/8" hole from the side, centered on the previous hole. Into this hole I insert a threaded insert - this will allow me to use a small bolt to "lock" the brass rod in place, so it doesn't turn in the hole while drilling it.

A small piece of steel mounted on the side of the ash was added when the threaded insert I used started wanting to strip out of the wood - the steel is there simply to hold the threaded insert in place in its hole.

Once the jig is complete, I take a 7" or 8" section of brass rod, and insert it into the jig. Using a center finder, I locate the center of the rod and use a center punch on it to locate it for the drill bit. I place the entire assembly on the drill press, and drill a 13/64" hole in the center of the brass rod to the drill bits full depth:

Drilling it to the full depth of the drill bit is necessary for the next step, which is tapping the hole for 10-24 thread.

Making the Nut

The next step is to tap the brass rod using a 10-24 tpi tap:

Tap to the full depth of the tap - on subsequent nuts, it's occasionally necessary to drill the center hole a little deeper to accommodate the tap.

Now its time to add the slot for the nut - you can skip this step if the nut is to be used for the bolts. I use a hack saw to make the slot:

Cut to a depth of about 1/8" to 3/16" or so, making sure the cut is level across the nut - then cut the nut off...

Learn how. Discover why. Build better.

1 of 3


Edge Tools



Copyright 2005-2018, and Wiktor Kuc.  All Rights Reserved.  Designated trademarks and brands are the property of their respective owners.
No part of the content from this website can be reproduced by any means without specific permission of the publisher.
Valid CSS!