Heller Files


Brought to you by How + Print

Nicholson Files


   
 

Making and Using Handtools


 
 

Rules, Squares, Straight Edges, Hack Saws, Screw Drivers and Wrenches by W. H. Vandervoort, 1897

1 of 5

 

No tool in the machinistís kit is more often referred to than the steel rule.

Upon it he depends in making all ordinary measurements and for the setting of his calipers and dividers. In first image below is shown a standard steel rule or scale.  They are made in various lengths, from one to forty-eight inches, with any desired gradation, no exceeding 1-100 of an inch in fineness.

For shop work the gradation most used is eights, sixteenths, thirty-seconds and sixty-fourths, on the four corners of the scale.  A scale graduated sixteenths, thirty-seconds, sixty-fourths and one-hundredths is convenient, and the 100ths graduations will serve for measurements when required in decimals.

Where all the work is measured by fractions, however, the former is the safest ruling to use, as there is then no danger of inadvertently mistaking a tenth for an eighth division, etc. 

For this reason, rules graduated in twelfths and fourteenths should not find their way into the machinistís tool box, as he will not have occasion to use these divisions, and their presence will call for greater care in selecting the proper division, with the loss of time incident to changing ends with and turning over the rule in order to get at the division required.

The end graduation, as shown below, is frequently very convenient in taking measurements in recesses where the length of the scale would prevent the use of the regular graduation.

Standard steel rules, as made by our leading makers, are remarkably accurate.  To be sure, the length varies slightly with the changes in temperature, but these changes are not ordinarily great, and the material measured is usually affected about the same amount in the same direction; so we may feel assured that any errors arising from this source are well within the limit of the personal error of the operator in making a measurement.

The late refinements in the manufacture of steel rules have enabled the production of very accurate tempered ones on comparatively thin steel.  What we usually know as the standard rule, however, is graduated on thick steel, and is not tempered.  The tempered rules possess the decided advantage of resistance to wear.

An untempered rule is easily mutilated, and soon rounds its corners through wear, making its ends unfit for reference.  The tempered rules may be classed as heavy, tempered, semi-flexible and flexible.  The heavy are about about one-tenth; the tempered, one-twentieth; the semi-flexible, one-fortieth, and the flexible one-eightieth of an inch thick. 

For general work the heavy or tempered will be found best suited.  The flexible are graduated on one side only, and are of value in measuring curved or irregular outlines.

In this connection it will be well to call attention to the gear rule show below.

Its application is in the sizing of gear blanks and where, by rule of thumb, two diameter pitches are added to the pitch diameter of the gear in obtaining the whole diameter.  Thus, if the pitch is No. 7 diametrical and the number of teeth 34, then the pitch diameter = 34-7=4-6/7 inches, and the blank or whole diameter = 4-6/7 +2/7=5- 1/7 inches, which can be taken directly from the scale.  This rule is of great convenience where many blanks for varying pitches and numbers of teeth are to be sized.

In the image above is shown a neat kink which will be found of value in taking measurement similar to the ones shown in the figure, as well as for setting inside calipers.  The hook may be quickly removed.  It is hardened, and in connection with a tempered rule forms a reliable tool.


Woodworker's Guide to Wood Collection only $79.99 at Shop Woodworking

1 of 5

Squares



Folding Rule



   

Copyright © 2005-2017, wkFineTools.com and Wiktor Kuc.  All Rights Reserved.  Designated trademarks and brands are the property of their respective owners.
No part of the content from this website can be reproduced by any means without specific permission of the publisher.
Valid CSS!